View CS497014-CVZ_4600655.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CS4970x4 Data Sheet
FEATURES
Multi-standard 32-bit High Definition Audio Decoding plus Post-Processing Supports high-definition audio formats including: -- Dolby Digital(R) Plus -- Dolby(R) TrueHD -- DTS-HD High Resolution Audio -- DTS-HD(R) Master
TM (R)
High Definition Audio Decoder DSP Family with Dual 32-bit DSP Engine Technology
Up to 12 Channels of 32-bit Serial Audio Input Customer Software Security Keys 16 Ch x 32-bit PCM Out with Dual 192 kHz SPDIF Tx Two SPITM/I2CTM ports One Parallel Port (144-pin LQFP package only) Large On-chip X, Y, and Program RAM & ROM SDRAM and Serial Flash Memory Support
Audio
-- DTS Express Additional Applications Library -- Dolby Digital(R) EX, Dolby(R) Pro Logic(R) IIz, Dolby Headphone 2(R), Dolby(R) Virtual Speaker 2(R), Audistry(R) -- DTS-ES 96/24TM Discrete 7.1, DTS-ESTM Discrete 7.1, DTSESTM Matrix 6.1, DTS Neo:6(R), DTS Neural SurroundTM -- DSD(R) -- MPEG-2 AACTM LC 5.1 -- SRS(R) CS2(R), SRS TruVolumeTM, SRS(R) TruSurround HD4TM, WOW HDTM, -- THX(R) Ultra2TM, THX(R) ReEQTM -- Thomson MP3 Surround -- Audyssey 2EQTM Module
Cirrus Logic's Applications Library -- Cirrus Original Multi-Channel Surround 2 (COMS2), Cirrus Band XpanderTM, Cirrus Virtualization Technology, Cirrus Intelligent Room Calibration 2 (IRC2) -- Crossbar Mixer, Signal Generator -- Advanced Post-Processors including: 7.1 Bass Manager, Tone Control, 11- Band Parametric EQ, Delay, 2:1/4:1 Decimator, 1:2/1:4 Upsampler
The CS4970x4 DSP family is an enhanced version of the CS4953x DSP family with higher overall performance. In addition to all the mainstream audio processing codes in onchip ROM that the CS4953x DSP offers, the CS4970x4 device family also supports the decoding of major high-definition audio formats. Additionally, the CS4970x4, a dual-core device, performs the high-definition audio decoding on the first core, leaving the second core available for audio post-processing and audio enhancement. The CS4970x4 device supports the most demanding audio post processing requirements. It provides an easy upgrade path to systems currently using the CS495xx or CS4953x device with minor hardware and software changes. Ordering Information See page 28 for ordering information.
Serial Control 1 12 Ch. Audio In / 6 Ch. SACD In
Serial Control 2
Parallel Control
GPIO
Debug
STC Coyote 32-bit DSP A D M A Coyote 32-bit DSP B P X Y TMR1 TMR2
S/PDIF
S/PDIF
P
X
Y
16 Ch PCM Audio Out Ext. Memory Controller PLL
Preliminary Product Information
This document contains information for a new product. Cirrus Logic reserves the right to modify this product without notice.
Copyright 2009 Cirrus Logic Nov `09 DS752PP8
http://www.cirrus.com
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
Table of Contents
1. Documentation Strategy ................................................................................................................ 4 2. Overview .......................................................................................................................................... 4
2.1 Migrating from the CS495xx(2) to the CS4970x4 ........................................................................................... 6 2.2 Licensing ......................................................................................................................................................... 6
3. Code Overlays ................................................................................................................................. 6 4. Hardware Functional Description ................................................................................................. 7
4.1 Coyote DSP Core ........................................................................................................................................... 7 4.1.1 DSP Memory ...................................................................................................................................... 7 4.1.2 DMA Controller ................................................................................................................................... 7 4.2 On-chip DSP Peripherals ................................................................................................................................ 7 4.2.1 Digital Audio Input Port (DAI) ............................................................................................................. 7 4.2.2 Digital Audio Output Port (DAO) ........................................................................................................ 8 4.2.3 Serial Control Port 1 & 2 (I2CTM or SPITM) ........................................................................................... 8 4.2.4 Parallel Control Port ........................................................................................................................... 8 4.2.5 External Memory Interface ................................................................................................................. 8 4.2.6 GPIO .................................................................................................................................................. 8 4.2.7 PLL-based Clock Generator ............................................................................................................... 8 4.3 DSP I/O Description ........................................................................................................................................ 8 4.3.1 Multiplexed Pins ................................................................................................................................. 8 4.3.2 Termination Requirements ................................................................................................................. 8 4.3.3 Pads ................................................................................................................................................... 9 4.4 Application Code Security ............................................................................................................................... 9
5. Characteristics and Specifications ............................................................................................. 10
5.1 Absolute Maximum Ratings .......................................................................................................................... 10 5.2 Recommended Operating Conditions ........................................................................................................... 10 5.3 Digital DC Characteristics ............................................................................................................................. 10 5.4 Power Supply Characteristics ........................................................................................................................11 5.5 Thermal Data (144-Pin LQFP) .......................................................................................................................11 5.6 Thermal Data (128-pin LQFP) .......................................................................................................................11 5.7 Switching Characteristics-- RESET# ........................................................................................................... 12 5.8 Switching Characteristics -- XTI .................................................................................................................. 12 5.9 Switching Characteristics -- Internal Clock .................................................................................................. 13 5.10 Switching Characteristics -- Serial Control Port - SPI Slave Mode ............................................................ 13 5.11 Switching Characteristics -- Serial Control Port - SPI Master Mode .......................................................... 14 5.12 Switching Characteristics -- Serial Control Port - I2C Slave Mode ............................................................ 15 5.13 Switching Characteristics -- Serial Control Port - I2C Master Mode .......................................................... 16 5.14 Switching Characteristics -- Parallel Control Port - Inte(R) Slave Mode ...................................................... 17 5.15 Switching Characteristics -- Parallel Control Port - Motorola(R) Slave Mode ............................................. 19 5.16 Switching Characteristics -- Digital Audio Slave Input Port ....................................................................... 21 5.17 Switching Characteristics -- DSD(R) Serial Input Port ................................................................................. 22 5.18 Switching Characteristics -- Digital Audio Output Port ............................................................................... 23 5.19 Switching Characteristics -- SDRAM Interface .......................................................................................... 24
6. Ordering Information .................................................................................................................... 28 7. Environmental, Manufacturing, and Handling Information ..................................................... 28 8. Device Pin-Out Diagram ............................................................................................................... 29
8.1 128-Pin LQFP Pin-Out Diagram ................................................................................................................... 29 8.2 144-Pin LQFP Pin-Out Diagram .................................................................................................................. 30
2
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
9. Package Mechanical Drawings ....................................................................................................31
9.1 128-Pin LQFP Package Drawing ..................................................................................................................31 9.2 144-Pin LQFP Package Drawing ..................................................................................................................32
10. Revision History ..........................................................................................................................33
List of Figures
Figure 1. RESET# Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Figure 2. XTI Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Figure 3. Serial Control Port - SPI Slave Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Figure 4. Serial Control Port - SPI Master Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Figure 5. Serial Control Port - I2C Slave Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Figure 6. Serial Control Port - I2C Master Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Figure 7. Parallel Control Port - Intel(R) Slave Mode Read Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Figure 8. Parallel Control Port - Intel Slave Mode Write Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Figure 9. Parallel Control Port - Motorola(R) Slave Mode Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Figure 10. Parallel Control Port - Motorola Slave Mode Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Figure 11. Digital Audio Input (DAI) Port Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Figure 12. DSD Serial Audio Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Figure 13. Digital Audio Port Output Timing Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Figure 14. Digital Audio Output Timing, Slave Mode (Relationship LRCLK to SCLK) . . . . . . . . . . . . . . . . . . . . . . . . .24 Figure 15. External Memory Interface - SDRAM Burst Read Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Figure 16. External Memory Interface - SDRAM Burst Write Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Figure 17. External Memory Interface - SDRAM Auto Refresh Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Figure 18. External Memory Interface - SDRAM Load Mode Register Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Figure 19. 128-Pin LQFP Pin-Out Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Figure 20. 144-Pin LQFP Pin-Out Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Figure 21. 128-Pin LQFP Package Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Figure 22. 144-Pin LQFP Package Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
List of Tables
Table 1. CS4970x4 Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Table 2. Device and Firmware Selection Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Table 3. CS4970x4 DSP Memory Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Table 4. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table 5. Environmental, Manufacturing, & Handling Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table 6. 128-Pin LQFP Package Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Table 7. 144-Pin LQFP Package Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DS752PP8
Copyright 2009 Cirrus Logic
3
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
1. Documentation Strategy
The CS4970x4 data sheet describes the CS4970x4 family of multichannel audio decoders. This document should be used in conjunction with the following documents when evaluating or designing a system around the CS4970x4 family of processors.
Table 1. CS4970x4 Related Documentation Document Name CS4970x4 Data Sheet Description This document A new consolidated documentation set that includes: * Detailed system design information including Typical Connection Diagrams, Boot-Procedures, Pin Descriptions, Etc. Also describes use of DSP Condenser tool. * Detailed firmware design information including signal processing flow diagrams and control API information Includes detailed firmware design information including signal processing flow diagrams and control API information
CS4953x4/CS4970x4 System Designer's Guide
AN288 - CS4953xx/CS497xxx Firmware User's Manual
The scope of the CS4970x4 Data Sheet is primarily the hardware specifications of the CS4970x4 family of devices. This includes hardware functionality, characteristic data, pinout, and packaging information. The intended audience for the CS4970x4 Data Sheet is the system PCB designer, MCU programmer, and the quality control engineer.
2. Overview
The CS4970x4 DSP Family, together with Cirrus Logic's comprehensive library of audio processing algorithms, enables the development of next-generation high-definition audio solutions. Cirrus Logic also provides a broad array of digital interface products and audio converters to meet your audio system-level design requirements. The CS4970x4 is available in 144-pin and 128-pin LQFP packages. The audio processing features of the CS4970x4 product family are a superset of audio features available in the CS4953xx product family. Please refer to Table 2 on page 5 for the speed and firmware features of CS4970x4 product family.
4
Copyright 2009 Cirrus Logic
DS752PP8
DS752PP8
Table 2. Device and Firmware Selection Guide
Device Decode Processor (DSP-A)1 Matrix-processor (DSP-A)1 Virtualizer-processor (DSP-B)1 Post-processor (DSP-B1
Stereo PCM
(4:1/2:1 Down-sampling and 1:2/1:4 Up-sampling Options)
Dolby PLIIz SRS Circle Surround II
(Stereo In)
2
APP
(Advanced Post-processing)
CS497014
300 MIPS
Multi-Channel PCM
(4:1/2:1 Down-sampling and 1:2/1:4 Up-sampling Options)
2
Cirrus Original Multi-Channel Surround (Effects / Reverb Processor) Crossbar (Down-mix / Upmix)
(Simultaneous Process)
Dolby Digital MPEG-2 AAC LC 5.1 Dolby Digital Plus Dolby TrueHD
Dolby Headphone 2 Dolby Virtual Speaker 2 SRS TruVolume
CS497004
300 MIPS
CS497024
300 MIPS
Same as CS49014 + DTS, DTS-ES, DTS96/24 DTS-HD Master Audio DTS-HD High Resolution Audio DTS Express
Same as CS49014 + DTS Neo:6
-Tone Control -Re-EQ -PEQ (up to 11 Bands) -Delay (Speaker to Listening Position Alignment and/or Lip Sync) -7.1 Bass Manager -Audio Manager -4:1/2;1 Downsampling2 SRS TruSurround HD4, WOW HD
Copyright 2009 Cirrus Logic 5
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
1. Processing may be restricted and dependent on firmware selected. Contact your Cirrus Logic FAE for concurrency matrix. 2. Downsampling and Upsampling functionality is located in the operating system. The Cirrus Decimator (Down-Sampler) is also available as a separate post-processing module that is described in the application note, AN288PPI.
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
2.1 Migrating from the CS495xx(2) to the CS4970x4
The CS4970x4 was designed to provide an easy upgrade path from the CS495xx & CS4953x. Although 144-pin versions of the two devices are virtually identical with respect to external system connection, there are some small differences the hardware designer should be aware of: * The PLL supply voltage on the CS4970x4 is 3.3V vs. 1.8V on the CS495xx. * The PLL filter topology is simpler when using the CS4970x4 rather than the CS495xx. * The CS4970x4 adds support for 6-channel DSD input. * The CS4970x4 adds support for TDM mode on both audio input and output ports. * The CS4970x4 does not support external SRAM operation. * The CS4970x4 external SDRAM bus speed is fixed at 150 MHz vs. the 120 MHz max bus speed for the CS495xx. Some firmware modules also support a 75 MHz CS4970x4 SDRAM bus speed. Please refer to AN304 for details. * The CS4970x4 CLKOUT pin can output XTALI or XTALI/2. The CS495xx can only output XTALI.
2.2 Licensing
Licenses are required for all of the third party audio decoding/processing algorithms listed below, including the application notes. Please contact your local Cirrus Sales representative for more information.
3. Code Overlays
The suite of software available for the CS4970x4 family consists of operating systems (OS) and a library of overlays. The overlays have been divided into three main groups called Decoders, Matrix-processors, and Postprocessors. All software components are defined in the following list: * OS/Kernel - Encompasses all non-audio processing tasks, including loading data from external memory, processing host messages, calling audio-processing subroutines, auto-detection, error concealment, etc. * Decoders - Any Module that initially writes data into the audio I/O buffers, e.g. AC-3TM, DTS, PCM, etc. All the decoding/processing algorithms listed require delivery of PCM or IEC61937-packed, compressed data via I2S- or LJ-formatted digital audio to the CS4970x4 from A/D converters, SPDIF Rx, HDMI Rx, etc. * Matrix-processors - Any module that processes audio I/O buffer PCM data in-place before the Postprocessors. Generally speaking, these modules alter the number of valid channels in the audio I/O buffer through processes like Virtualization (n 2 channels) or Matrix Decoding (2 n channels). Examples are Dolby ProLogic IIx and DTS Neo:6. * Virtualizer-processor - Any module that encodes PCM data into fewer output channels than input channels (n 2 channels) with the effect of providing "phantom" speakers to represent the physical audio channels that were eliminated. Examples are Dolby Headphone(R) 2 and Dolby Virtual Speaker(R) 2. Generally speaking, these modules reduce the number of valid channels in the audio I/O buffer. * Post-processors - Any module that processes audio I/O buffer PCM data in-place after the Matrix-Processors. Examples are Bass Management, Audio Manager, Tone Control, EQ, Delay, Customer-specific Effects, Dolby Headphone/Virtual Speaker, etc. The overlay structure reduces the time required to reconfigure the DSP when a processing change is requested. Each overlay can be reloaded independently without disturbing the other overlays. For example, when a new decoder is selected, the OS, matrix-, and post-processors do not need to be reloaded -- only the new decoder (the same is true for the other overlays).
6 Copyright 2009 Cirrus Logic DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
4. Hardware Functional Description
4.1 Coyote DSP Core
The CS4970x4 is a dual-core Coyote DSP with separate X and Y data and P code memory spaces. Each core is a high-performance, 32-bit, user-programmable, fixed-point DSP that is capable of performing two multiply accumulate (MAC) operations per clock cycle. Each core has eight 72-bit accumulators, four X- and four Y-data registers, and 12 index registers. Both DSP cores are coupled to a flexible DMA engine. The DMA engine can move data between peripherals such as the digital audio input (DAI) and digital audio output (DAO), external memory, or any DSP core memory, all without the intervention of the DSP. The DMA engine offloads data move instructions from the DSP core, leaving more MIPS available for signal processing instructions. CS4970x4 functionality is controlled by application codes that are stored in on-board ROM or downloaded to the CS4970x4 from a host MCU or external FLASH/EEPROM. Users can choose to use standard audio decoder and post-processor modules which are available from Cirrus Logic. The CS4970x4 is suitable for Audio Decoder, Audio Post-processor, Audio Encoder, DVD Audio/Video Player, and Digital Broadcast Decoder applications. 4.1.1 DSP Memory Each DSP core has its own on-chip data and program RAM and ROM and does not require external memory for any of today's popular audio algorithms including Dolby Digital Surround EX, AAC Multichannel, DTS-ES 96/24, and THX Ultra2. However, if the end-system design requires support of the new high-definition audio formats, external SDRAM will be needed to support Dolby TrueHD and DTS-HD Master Audio. The memory maps for the DSPs are as follows. All memory sizes are composed of 32-bit words.
Table 3. CS4970x4 DSP Memory Sizes
Memory Type DSP A DSP B
X Y P
16k SRAM, 32k ROM 24k SRAM, 32k ROM 8k SRAM, 32k ROM
10k SRAM, 8k ROM 16k SRAM, 16k ROM 8k SRAM, 24k ROM
4.1.2 DMA Controller The powerful 12-channel DMA controller can move data between 8 on-chip resources. Each resource has its own arbiter: X, Y, and P RAM/ROMs on DSP A; X, Y, and P RAM/ROMs on DSP B; external memory; and the peripheral bus. Modulo and linear addressing modes are supported, with flexible start address and increment controls. The service interval for each DMA channel as well as up to 6 interrupt events, is programmable.
4.2 On-chip DSP Peripherals
4.2.1 Digital Audio Input Port (DAI) The 12-channel (6 line) DAI port supports a wide variety of data input formats. The port is capable of accepting PCM, IEC61937, or DSD. Up to 32-bit word lengths are supported. Up to 6 channels of DSD are supported and internally converted to PCM before processing. Additionally support is provided for audio data input to the DSP via the DAI from an HDMI receiver.
DS752PP8
Copyright 2009 Cirrus Logic
7
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
The port has two independent slave-only clock domains. Each data input can be independently assigned to a clock domain. The sample rate of the input clock domains can be determined automatically by the DSP, which off-loads the task of monitoring the SPDIF receiver from the host. A time-stamping feature allows the input data to be sample-rate converted via software. 4.2.2 Digital Audio Output Port (DAO) There are two DAO ports. Each port can output 8 channels of up to 32-bit PCM data. The port supports data rates from 32 kHz to 192 kHz. Each port can be configured as an independent clock domain in slave mode, or the ratio of the two clocks can be set to even multiples of each other in master mode. The two ports can also be ganged together into a single clock domain. Each port has one serial audio pin that can be configured as a 192 kHz SPDIF transmitter (data with embedded clock on a single line). 4.2.3 Serial Control Port 1 & 2 (I2CTM or SPITM) There are two on-chip serial control ports that are capable of operating as master or slave in either I2C or SPI modes. SCP1 defaults to slave operation. It is dedicated for external host-control and supports an external clock up to 50 MHz in SPI mode. This high clock speed enables very fast code download, control or data delivery. SCP2 defaults to master mode and is dedicated for booting from external serial Flash memory or for audio sub-system control. 4.2.4 Parallel Control Port The CS4970x4 parallel port supports both Motorola(R) and Intel(R) interfaces. It can be used for both control and data delivery. The parallel port pins are multiplexed with serial control port 2 and are available in the 144-pin package. 4.2.5 External Memory Interface The external memory interface controller supports up to 128 Mbits of SDRAM, using a 16-bit data bus. 4.2.6 GPIO Many of the CS4970x4 peripheral pins are multiplexed with GPIO. Each GPIO can be configured as an output, an input, or an input with interrupt. Each input-pin interrupt can be configured as rising edge, falling edge, active-low, or active-high. 4.2.7 PLL-based Clock Generator The low-jitter PLL generates integer or fractional multiples of a reference frequency which are used to clock the DSP core and peripherals. Through a second PLL divider chain, a dependent clock domain can be output on the DAO port for driving audio converters. The CS4970x4 defaults to running from the external reference frequency and can be switched to use the PLL output after overlays have been loaded and configured, either through master boot from an external FLASH or through host control. A built-in crystal oscillator circuit with a buffered output is provided. The buffered output frequency ratio is selectable between 1:1 (default) or 2:1.
4.3 DSP I/O Description
4.3.1 Multiplexed Pins Many of the CS4970x4 pins are multi-functional. For details on pin functionality please refer to the CS4970x4 System Designer's Guide. 4.3.2 Termination Requirements Open-drain pins on the CS4970x4 must be pulled high for proper operation. Please refer to the CS4970x4 System Designer's Guide to identify which pins are open-drain and what value of pull-up resistor is required for proper operation.
8
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
Mode select pins on the CS4970x4 are used to select the boot mode upon the rising edge of reset. A detailed explanation of termination requirements for each communication mode select pin can be found in the CS4970x4 System Designer's Guide. 4.3.3 Pads The CS4970x4 I/O operate from the 3.3 V supply and are 5 V tolerant.
4.4 Application Code Security
The external program code may be encrypted by the programmer to protect any intellectual property it may contain. A secret, customer-specific key is used to encrypt the program code that is to be stored external to the device.
DS752PP8
Copyright 2009 Cirrus Logic
9
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
5. Characteristics and Specifications
Note: All data sheet minimum and maximum timing parameters are guaranteed over the rated voltage and temperature. All data sheet
typical parameters are measured under the following conditions: T = 25 C, CL = 20 pF, VDD = 1.8 V, VDDA = VDDIO = 3.3 V, GNDD = GNDIO = GNDA = 0 V.
5.1 Absolute Maximum Ratings
(GNDD = GNDIO = GNDA = 0 V; all voltages with respect to 0 V) Parameter DC power supplies: Core supply PLL supply I/O supply |VDDA - VDDIO| Symbol VDD VDDA VDDIO Iin Vfilt Vinio Tstg Min -0.3 -0.3 -0.3 -0.3 -0.3 -65 Max 2.0 3.6 3.6 0.3 +/- 10 3.6 5.0 150 Unit V V V V mA V V C
Input pin current, any pin except supplies Input voltage on PLL_REF_RES Input voltage on I/O pins Storage temperature
Caution: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes.
5.2 Recommended Operating Conditions
(GNDD = GNDIO = GNDA = 0 V; all voltages with respect to 0 V) Parameter DC power supplies: Core supply PLL supply I/O supply |VDDA - VDDIO| Commercial Grade (CQZ/CVZ) Symbol VDD VDDA VDDIO TA 0 +25 + 70 C Min 1.71 3.13 3.13 Typ 1.8 3.3 3.3 0 Max 1.89 3.46 3.46 Unit V V V V
Ambient operating temperature
Note: It is recommended that the 3.3 V IO supply come up ahead of or simultaneously with the 1.8 V core supply.
5.3 Digital DC Characteristics
(Measurements performed under static conditions.) Parameter High-level input voltage Low-level input voltage, except XTI Low-level input voltage, XTI Input Hysteresis High-level output voltage (IO = -4mA), except XTI, SDRAM pins Low-level output voltage (IO = 4mA), except XTI, SDRAM pins SDRAM High-level output voltage (IO = -8mA) SDRAM Low-level output voltage (IO = 8mA) Input leakage current (all digital pins with internal pullup resistors disabled) Symbol VIH VIL VILXTI Vhys VOH VOL VOH VOL IIN VDDIO * 0.9 VDDIO * 0.9 Min 2.0 Typ 0.4 VDDIO * 0.1 VDDIO * 0.1 5 Max 0.8 0.6 Unit V V V V V V V V A
10
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
Parameter Input leakage current (all digital pins with internal pullup resistors enabled, and XTI)
Symbol IIN-PU
Min -
Typ -
Max 70
Unit A
5.4 Power Supply Characteristics
(Measurements performed under operating conditions.) Parameter Power supply current: Core and I/O operating: VDD1 PLL operating: VDDA With external memory and most ports operating: VDDIO
1.Dependent on application firmware and DSP clock speed.
Min -
Typ 500 3.5 120
Max -
Unit mA mA mA
5.5 Thermal Data (144-Pin LQFP)
Parameter Thermal Resistance (Junction to Ambient) Two-layer Board1 Four-layer Board2 Thermal Resistance (Junction to Top of Package) Two-layer Board1 Four-layer Board2 Symbol Min Typ 48 40 .39 .33 Max C / Watt Unit C / Watt
ja jt
5.6 Thermal Data (128-pin LQFP)
Parameter Thermal Resistance (Junction to Ambient) Two-layer Board1 Four-layer Board2 Thermal Resistance (Junction to Top of Package) Two-layer Board1 Four-layer Board2 Symbol Min
-
Typ
53 44 .45 .39
Max
-
Unit
C / Watt
ja jt
-
C / Watt
Notes: 1.Two-layer board is specified as a 76 mm X 114 mm, 1.6 mm thick FR-4 material with 1-oz copper covering 20% of the top and bottom
layers.
2.Four-layer board is specified as a 76 mm X 114 mm, 1.6 mm thick FR-4 material with 1-oz copper covering 20% of the top and bottom layers and 0.5-oz copper covering 90% of the internal power plane and ground plane layers. 3.To calculate the die temperature for a given power dissipation
j = Ambient Temperature + [ (Power Dissipation in Watts) * ja ]
4.To calculate the case temperature for a given power dissipation
c = j - [ (Power Dissipation in Watts) * jt ]
DS752PP8
Copyright 2009 Cirrus Logic
11
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
5.7 Switching Characteristics-- RESET#
Parameter RESET# minimum pulse width low All bidirectional pins high-Z after RESET# low Configuration pins setup before RESET# high Configuration pins hold after RESET# high Symbol Trstl Trst2z Trstsu Trsthld Min 1 50 20 Max 100 Unit s ns ns ns
RESET#
HS[3:0] All Bidirectional Pins Trst2z Trstl
Trstsu Trsthld
Figure 1. RESET# Timing
5.8 Switching Characteristics -- XTI
Parameter External Crystal operating frequency1 XTI period XTI high time XTI low time External Crystal Load Capacitance (parallel resonant)2 External Crystal Equivalent Series Resistance Symbol Fxtal Tclki Tclkih Tclkil CL ESR Min 12.288 41 16.4 16.4 10 Max 24.576 81.4 18 50 Unit MHz ns ns ns pF
1. Part characterized with the following crystal frequency values: 12.288 and 24.576 MHz. 2. CL refers to the total load capacitance as specified by the crystal manufacturer. Crystals which require a CL outside this range should be avoided. The crystal oscillator circuit design should follow the crystal manufacturer's recommendation for load capacitor selection.
XTI
t clkih Tclki
Figure 2. XTI Timing
12 Copyright 2009 Cirrus Logic DS752PP8
t clkil
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
5.9 Switching Characteristics -- Internal Clock
Parameter Internal DCLK frequency1 CS497004-CQZ CS497004-CQZR CS497024-CVZ CS497024-CVZR CS497024-CVZ CS497024-CVZR Internal DCLK period1 CS497004-CQZ CS497004-CQZR CS497024-CVZ CS497024-CVZR CS497024-CVZ CS497024-CVZR DCLKP 6.7 1/Fxtal Symbol Fdclk Fxtal 150 Min Max Unit MHz
ns
1.After initial power-on reset, Fdclk = Fxtal. After initial kickstart commands, the PLL is locked to max Fdclk and remains locked until the next power-on reset.
5.10 Switching Characteristics -- Serial Control Port - SPI Slave Mode
.
Parameter SCP_CLK frequency1 SCP_CS# falling to SCP_CLK rising SCP_CLK low time SCP_CLK high time Setup time SCP_MOSI input Hold time SCP_MOSI input SCP_CLK low to SCP_MISO output valid SCP_CLK falling to SCP_IRQ# rising SCP_CS# rising to SCP_IRQ# falling SCP_CLK low to SCP_CS# rising SCP_CS# rising to SCP_MISO output high-Z SCP_CLK rising to SCP_BSY# falling Symbol fspisck tspicss tspickl tspickh tspidsu tspidh tspidov tspiirqh tspiirql tspicsh tspicsdz tspicbsyl Min 24 20 20 5 5 0 24 20 3*DCLKP+20 Typical Max 25 11 20 Units MHz ns ns ns ns ns ns ns ns ns ns ns
1. The specification fspisck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application. Flow control using the SCP_BSY# pin should be implemented to prevent overflow of the input data buffer.At boot the maximum speed is Fxtal/3.
DS752PP8
Copyright 2009 Cirrus Logic
13
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
tspicss
SCP_CS#
tspickl 0 1 2 6 7 0 5 6 7 tspicsh
SCP_CLK
fspisck tspickh A6 tspidsu tspidh tspidov MSB tspiirqh LSB tspiirql tspicsdz A5 A0 R/W MSB LSB
SCP_MOSI
SCP_MISO
SCP_IRQ#
tspibsyl
SCP_BSY#
Figure 3. Serial Control Port - SPI Slave Mode Timing
5.11 Switching Characteristics -- Serial Control Port - SPI Master Mode
Parameter SCP_CLK frequency1, 2
3
Symbol fspisck tspicss tspickl tspickh tspidsu tspidh tspidov tspicsl tspicsh tspicsx tspidz
Min 18 18 11 5 7 -
Typical 11*DCLKP + (SCP_CLK PERIOD)/2
Max Fxtal/2 11 -
Units MHz ns ns ns ns ns ns ns ns ns ns
SCP_CS# falling to SCP_CLK rising SCP_CLK low time SCP_CLK high time Setup time SCP_MISO input Hold time SCP_MISO input
SCP_CLK low to SCP_MOSI output valid SCP_CLK low to SCP_CS# falling SCP_CLK low to SCP_CS# rising Bus free time between active SCP_CS# SCP_CLK falling to SCP_MOSI output high-Z
11*DCLKP + (SCP_CLK PERIOD)/2 3*DCLKP
20
-
1. The specification fspisck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application. 2. See Section 5.8. 3. SCP_CLK PERIOD refers to the period of SCP_CLK as being used in a given application. It does not refer to a tested parameter.
14
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
.
tspicsx tspicss
EE_CS#
tspicsl tspickl 0 1 2 6 7 0 5 6 7 tspicsh
SCP_CLK
fspisck tspickh A6 tspidsu tspidh tspidov MSB LSB tspidz A5 A0 R/W MSB LSB
SCP_MISO
SCP_MOSI
Figure 4. Serial Control Port - SPI Master Mode Timing
5.12 Switching Characteristics -- Serial Control Port - I2C Slave Mode
Parameter SCP_CLK frequency1 SCP_CLK low time SCP_CLK high time SCP_SCK rising to SCP_SDA rising or falling for START or STOP condition START condition to SCP_CLK falling SCP_CLK falling to STOP condition Bus free time between STOP and START conditions Setup time SCP_SDA input valid to SCP_CLK rising Hold time SCP_SDA input after SCP_CLK falling SCP_CLK low to SCP_SDA out valid SCP_CLK falling to SCP_IRQ# rising NAK condition to SCP_IRQ# low SCP_CLK rising to SCB_BSY# low Symbol fiicck tiicckl tiicckh tiicckcmd tiicstscl tiicstp tiicbft tiicsu tiich tiicdov tiicirqh tiicirql tiicbsyl Min 1.25 1.25 1.25 1.25 2.5 3 100 20 3*DCLKP + 20 3*DCLKP + 20 18 3*DCLKP + 40 Typical Max 400 Units kHz s s s s s s ns ns ns ns ns ns
1. The specification fiicck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application. Flow control using the SCP_BSY# pin should be implemented to prevent overflow of the input data buffer.
DS752PP8
Copyright 2009 Cirrus Logic
15
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
tiicckcmd 0 1
tiicckl 6
tiicr 7 8
tiicf 0 1 6 7 8
tiicckcmd
SCP_CLK
tiicstscl tiicckh A6 A0 tiicdov R/W ACK MSB tiicirqh tiicsu tiich fiicck LSB ACK tiicirql tiicstp tiicbft
SCP_SDA
SCP_IRQ#
tiiccbsyl
SCP_BSY#
Figure 5. Serial Control Port - I2C Slave Mode Timing
5.13 Switching Characteristics -- Serial Control Port - I2C Master Mode
Parameter SCP_CLK frequency SCP_CLK low time SCP_CLK high time SCP_SCK rising to SCP_SDA rising or falling for START or STOP condition START condition to SCP_CLK falling SCP_CLK falling to STOP condition Bus free time between STOP and START conditions Setup time SCP_SDA input valid to SCP_CLK rising Hold time SCP_SDA input after SCP_CLK falling SCP_CLK low to SCP_SDA out valid
1
Symbol fiicck tiicckl tiicckh tiicckcmd tiicstscl tiicstp tiicbft tiicsu tiich tiicdov
Min 1.25 1.25 1.25 1.25 2.5 3 100 20 -
Max 400 -
Units kHz s s s
36
s s s ns ns ns
1. The specification fiicck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application.
16
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
tiicckcmd 0 1
tiicckl 6
tiicr 7 8
tiicf 0 1 6 7 8
tiicckcmd
SCP_CLK
tiicstscl tiicckh A6 A0 tiicdov R/W ACK MSB fiicck LSB ACK tiicstp tiicbft
SCP_SDA
tiicsu
tiich
Figure 6. Serial Control Port - I2C Master Mode Timing
5.14 Switching Characteristics -- Parallel Control Port - Intel(R) Slave Mode
Parameter Address setup before PCP_CS# and PCP_RD# low or PCP_CS# and PCP_WR# low Address hold time after PCP_CS# and PCP_RD# low or PCP_CS# and PCP_WR# high Read Delay between PCP_RD# then PCP_CS# low or PCP_CS# then PCP_RD# low Data valid after PCP_CS# and PCP_RD# low PCP_CS# and PCP_RD# low for read Data hold time after PCP_CS# or PCP_RD# high Data high-Z after PCP_CS# or PCP_RD# high PCP_CS# or PCP_RD# high to PCP_CS# and PCP_RD# low for next read1 PCP_CS# or PCP_RD# high to PCP_CS# and PCP_WR# low for next write1 PCP_RD# rising to PCP_IRQ# rising Write Delay between PCP_WR# then PCP_CS# low or PCP_CS# then PCP_WR# low Data setup before PCP_CS# or PCP_WR# high PCP_CS# and PCP_WR# low for write Data hold after PCP_CS# or PCP_WR# high PCP_CS# or PCP_WR# high to PCP_CS# and PCP_RD# low for next read1 PCP_CS# or PCP_WR# high to PCP_CS# and PCP_WR# low for next write1 PCP_WR# rising to PCP_BSY# falling
DS752PP8
Symbol tias tiah
Min 5 5
Typical
Max -
Unit ns ns
ticdr tidd tirpw tidhr tidis tird tirdtw tirdirqhl ticdw tidsu tiwpw tidhw tiwtrd tiwd tiwrbsyl
0 24 8 30 30 0 8 24 8 30 30 2*DCLKP + 20
18 18 12 -
ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
17
Copyright 2009 Cirrus Logic
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
1. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application. Hardware handshaking on the PCP_BSY# pin/bit should be observed to prevent overflowing the input data buffer. CS4953x4/CS4970x4 System Designer's Guide should be consulted for the firmware speed limitations.
P C P _ A [3 :0 ] t iah P C P _ D [7 :0 ] PCP_CS# t ic dr PC P _W R # PC P _R D # t irdirq h P C P _ IR Q # t irp w t ias t id d
LSP MSP
t id hr t idis t ird t irdtw
Figure 7. Parallel Control Port - Intel(R) Slave Mode Read Cycle
P C P _A [3:0]
t iah
P C P _D [7:0] P C P _C S #
t ias
LS P
MSP
t id hw t idsu t iw pw t iw d t iw trd
t icdw
P C P _R D # P C P _W R #
t iw rbs yl P C P _B S Y #
Figure 8. Parallel Control Port - Intel Slave Mode Write Cycle
18
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
5.15 Switching Characteristics -- Parallel Control Port - Motorola(R) Slave Mode
Parameter Address setup before PCP_CS# and PCP_DS# low Address hold time after PCP_CS# and PCP_DS# low Read Delay between PCP_DS# then PCP_CS# low or PCP_CS# then PCP_DS# low Data valid after PCP_CS# and PCP_DS# low with PCP_R/W# high PCP_CS# and PCP_DS# low for read Data hold time after PCP_CS# or PCP_DS# high after read Data high-Z after PCP_CS# or PCP_DS# high after read PCP_CS# or PCP_DS# high to PCP_CS# and PCP_DS# low for next read1 PCP_CS# or PCP_DS# high to PCP_CS# and PCP_DS# low for next write1 PCP_RW# rising to PCP_IRQ# falling Write Delay between PCP_DS# then PCP_CS# low or PCP_CS# then PCP_DS# low Data setup before PCP_CS# or PCP_DS# high PCP_CS# and PCP_DS# low for write PCP_R/W# setup before PCP_CS# AND PCP_DS# low PCP_R/W# hold time after PCP_CS# or PCP_DS# high Data hold after PCP_CS# or PCP_DS# high PCP_CS# or PCP_DS# high to PCP_CS# and PCP_DS# low with PCP_R/W# high for next read1 PCP_CS# or PCP_DS# high to PCP_CS# and PCP_DS# low for next write1 PCP_RW# rising to PCP_BSY# falling tmcdw tmdsu tmwpw tmrwsu tmrwhld tmdhw tmwtrd tmwd tmrwbsyl 0 8 24 24 8 8 30 30 2*DCLKP + 20 ns ns ns ns ns ns ns ns ns tmcdr tmdd tmrpw tmdhr tmdis tmrd tmrdtw tmrwirqh 0 24 8 30 30 19 18 12 ns ns ns ns ns ns ns ns Symbol tmas tmah Min 5 5 Max Unit ns ns
1. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application. Hardware handshaking on the PCP_BSY# pin/bit should be observed to prevent overflowing the input data buffer. CS4953x4/CS4970x4 System Designer's Guide should be consulted for the firmware speed limitations.
DS752PP8
Copyright 2009 Cirrus Logic
19
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
P C P_A[3:0]
t m as
P C P_AD [7:0] PC P_C S# PC P_W R # PC P_D S#
t m ah
LSP MSP
t m dhr t m dd t m rw su t m cdr t m rp w t m rd t m dis t m rd tw t m rw hld
t m rw irqh P C P_IR Q #
Figure 9. Parallel Control Port - Motorola(R) Slave Mode Read Cycle Timing
P C P _ A [3 :0 ] t m as
P C P _ A D [7 :0 ] PCP_CS#
t m ah LSP t m dsu t m cdw t m dhw t m w pw
MSP
t m r w h ld t m wd
t m rw irq l
PCP_W R#
t m rw s u
PCP_DS# P C P _ IR Q #
t m w trd
Figure 10. Parallel Control Port - Motorola Slave Mode Write Cycle Timing
20
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
5.16 Switching Characteristics -- Digital Audio Slave Input Port
Parameter DAI_SCLK period DAI_SCLK duty cycle Setup time DAI_DATAn Hold time DAI_DATAn Symbol Tdaiclkp tdaidsu tdaidh Min 40 45 10 5 Max 55 Unit ns % ns ns
DAI_SC LK t daidsu DAI_DATAn t daidh
Figure 11. Digital Audio Input (DAI) Port Timing Diagram
DS752PP8
Copyright 2009 Cirrus Logic
21
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
5.17 Switching Characteristics -- DSD(R) Serial Input Port
Parameter DSD_SCLK Pulse Width Low DSD_SCLK Pulse Width High DSD_SCLK Frequency (64x Oversampled) DSD_A / _B valid to DSD_SCLK rising setup time DSD_SCLK rising to DSD_A or DSD_B hold time Symbol tsclkl tsclkh tsdlrs tsdh Min 78 78 1.024 20 20 Typ Max 3.2 Unit ns ns MHz ns ns
Figure 12. DSD Serial Audio Input Timing
22
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
5.18 Switching Characteristics -- Digital Audio Output Port
Parameter DAO_MCLK period DAO_MCLK duty cycle DAO_SCLK period for Master or Slave mode1
1,2
Symbol Tdaomclk Tdaosclk tdaomsck tdaomlrts tdaomstlr tdaomdv
Min 40 45 40 40 -
Max 55 60 19 8 8 10
Unit ns % ns % ns ns ns ns
DAO_SCLK duty cycle for Master or Slave mode1 Master Mode (Output A1 Mode) DAO_SCLK delay from DAO_MCLK rising edge, DAO_MCLK as an input DAO_SCLK delay from DAO_LRCLK transition, respectively3 DAO_LRCLK delay from DAO_SCLK transition, respectively DAO1_DATA[3..0], DAO2_DATA[1..0] delay from DAO_SCLK transition3 Slave Mode (Output A0 Mode)4 DAO1_DATA[3..0], DAO2_DATA[1..0] delay from DAO_SCLK transition3 DAO_LRCLK delay from DAO_SCLK transition, respectively3 DAO_SCLK delay from DAO_LRCLK transition, respectively3
3
tdaosdv tdaosstlr tdaoslrts
-
15 30 15
ns ns ns
1. Master mode timing specifications are characterized, not production tested. 2. Master mode is defined as the CS4970x4 driving both DAO_SCLK, DAO_LRCLK. When MCLK is an input, it is divided to produce DAO_SCLK, DAO_LRCLK. 3. This timing parameter is defined from the non-active edge of DAO_SCLK. The active edge of DAO_SCLK is the point at which the data is valid. 4. Slave mode is defined as DAO_SCLK, DAO_LRCLK driven by an external source.
tdaomlclk DAO_MCLK tdaomsck DAO_SCLK tdaomdv DAOn_DATAn tdaomlrts DAO_LRCLK
DAO_LRCLK DAOn_DATAn DAO_SCLK DAO_MCLK
tdaomclk
tdaomsck
tdaomstlr
Note: In these diagrams, Falling edge is the inactive edge of DAO_SCLK Figure 13. Digital Audio Port Output Timing Master Mode
DS752PP8
Copyright 2009 Cirrus Logic
23
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
tdaosclk tdaosstlr DAO_LRCLK DAO_LRCLK DAO_SCLK DAO_SCLK tdaosclk DAOn_DATAn tdaosdv tdaoslrts
Note: In these diagrams, Falling edge is the inactive edge of DAO_SCLK Figure 14. Digital Audio Output Timing, Slave Mode (Relationship LRCLK to SCLK)
5.19 Switching Characteristics -- SDRAM Interface
Refer to Figure 15 through Figure 18.
(SD_CLKOUT = SD_CLKIN) Parameter SD_CLKIN high time SD_CLKIN low time SD_CLKOUT rise/fall time SD_CLKOUT Frequency SD_CLKOUT duty cycle SD_CLKOUT rising edge to signal valid Signal hold from SD_CLKOUT rising edge SD_CLKOUT rising edge to SD_DQMn valid SD_DQMn hold from SD_CLKOUT rising edge SD_DATA valid setup to SD_CLKIN rising edge SD_DATA valid hold to SD_CLKIN rising edge SD_CLKOUT rising edge to ADDRn valid tsdcmdv tsdcmdh tsddqv tsddqh tsddsu tsddh tsdav 1.38 1.3 1.38 3.8 45 1.1 3.8 Symbol tsdclkh tsdclkl tsdclkrf Min 2.3 2.3 150 55 3.8 Typical Max 1 Unit ns ns ns MHz % ns ns ns ns ns ns ns
24
Copyright 2009 Cirrus Logic
DS752PP8
DS752PP8 Copyright 2009 Cirrus Logic 25
SD_CLKOUT
tsdcmdv
SD_CS#
tsdcmdh
tsdclkrf
SD_RAS#
SD_CAS# SD_WE# SD_DQMn
tsddqv
00
tsddqh
11
SD_An
tsdav
CAS=2 SD_Dn
tsddsu
tsddh
LSP0 MSP0 LSP1 MSP1 LSP2 MSP2 LSP3 MSP3
SD_CLKIN
tsdclkl
tsdclkh
Figure 15. External Memory Interface - SDRAM Burst Read Cycle
SD_CLKOUT
tsdcmdv
SD_CS#
tsdcmdh
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
SD_RAS#
SD_CAS#
SD_WE#
SD_Dn
LSP0
MSP0
LSP1
MSP1
LSP2
MSP2
LSP3
MSP3
tsdav
SD_An
SD_DQMn
00
11
tsddqv
tsddqh
Figure 16. External Memory Interface - SDRAM Burst Write Cycle
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
SD_CLKOUT
tsdcmdv SD_CS#
tsdcmdv
tsdcmdh
SD_RAS#
SD_CAS#
SD_WE#
SD_DQMn
SD_An
SD_Dn
Figure 17. External Memory Interface - SDRAM Auto Refresh Cycle
26
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
SD_CLKOUT
tsdcmdv SD_CS#
tsdcmdh
SD_RAS#
SD_CAS#
SD_WE#
SD_DQMn
SD_An
OPCODE
SD_Dn
Figure 18. External Memory Interface - SDRAM Load Mode Register Cycle
DS752PP8
Copyright 2009 Cirrus Logic
27
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
6. Ordering Information
The CS4970x4 family part number is described as follows:
CS497NNI-XYZ
where NN - Product Number Variant I - ROM ID Number X - Product Grade Y - Package Type Z - Lead (Pb) Free
Table 4. Ordering Information
Part No. Grade Temp. Range Container Package
CS497004-CQZ CS497004-CQZR CS497014-CVZ CS47014-CVZR CS497024-CVZ CS497024-CVZR
Commercial Commercial Commercial Commercial Commercial Commercial
0 to +70 C 0 to +70 C 0 to +70 C 0 to +70 C 0 to +70 C 0 to +70 C
Tray Reel Tray Reel Tray Reel
144-pin LQFP
128-pin LQFP
128-pin LQFP
Note: Please contact the factory for availability of the -D (automotive grade) package.
7. Environmental, Manufacturing, and Handling Information
Table 5. Environmental, Manufacturing, & Handling Information
Model Number Peak Reflow Temp MSL Rating* Max Floor Life
CS497004-CQZ CS497004-CQZR CS497014-CVZ CS47014-CVZR CS497024-CVZ CS497024-CVZR
260 C 260 C 260 C 260 C 260 C 260 C
3 3 3 3 3 3
7 Days 7 Days 7 Days 7 Days 7 Days 7 Days
* MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020.
28
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
8. Device Pin-Out Diagram
8.1 128-Pin LQFP Pin-Out Diagram
GPIO37, SCP1_BSY#, PCP_BSY# GPIO34, SCP1__MISO / SDA
GPIO33, SCP1_MOSI
GPIO35, SCP1_CLK
SD_BA1, EXT_A14
SD_BA0, EXT_A13
110 SD_CS#
105 GNDIO5
120 VDDIO6
115 GND5
125 VDD6
SD_A10, EXT_A10
EXT_CS1#
SD_RAS#
SD_CAS#
EXT_OE#
EXT_A19
EXT_A18
EXT_A17
EXT_A16
EXT_A15
SD_WE#
GNDIO6
GND6
RESET#
VDD5
GPIO38, PCP_WR# / DS#, SCP2_CLK GPIO11, PCP_A3, AS#, SCP2_MISO / SDA GPIO10, PCP_A2 / A10, SCP2_MOSI GPOI9, SCP1_IRQ# GPIO8, PCP_IRQ#, SCP2_IRQ# GPIO7, SCP1_CS#, IOWAIT GPIO6, PCP_CS#, SCP2_CS# VDDIO7 GNDIO7
1
SD_A0, EXT_A0 SD_A1, EXT_A1 100 VDDIO5 SD_A2, EXT_A2
5
GND4 SD_A3, EXT_A3 SD_A4, EXT_A4 95 VDD4 EXT_CS2# SD_A5, EXT_A5 GNDIO4 SD_A6, EXT_A6 90 SD_A7, EXT_A7 VDDIO4 SD_A8, EXT_A8 SD_A9, EXT_A9 GND3 85 SD_A11, EXT_A11
GPIO3, DDAC 10 GPIO2 VDD7 GPIO1 GPIO0, EE_CS# GND7 15 XTAL_OUT XTI XTO GNDA PLL_REF_RES 20 VDDA (3.3V) VDD8 GPIO14, DAI1_DATA3, TM3, DSD3 GPIO13, DAI1_DATA2, TM2, DSD2 GND8 25 GPIO12, DAI1_DATA1, TM1, DSD1 DAI1_DATA0, TM0, DSD0 VDDIO8 DAI1_SCLK, DSD_CLK DAI1_LRCLK, DSD4 30 GNDIO8 GPIO42, BDI_REQ# , DAI2_LRCLK, PCP_IRQ# / BSY# GPIO43, BDI_CLK, DAI2_SCLK BDI_DATA, DAI2_DATA, DSD5 GPIO26, DAO2_DATA3 / XMTB 35 DBDA DBCK GPIO20, DAO2_DATA2 DAO_MCLK 40 GND1 45 GPIO23, DAO2_LRCLK GPIO17, DAO1_DATA3 / XMTA VDDIO1 50 VDD2 55 SD_D5, EXT_D5 60
CS497xx4
128-Pin LQFP
SD_A12, EXT_A12 VDD3 SD_CLKEN SD_CLKIN 80 SD_CLKOUT SD_DQM1 SD_D8, EXT_D8 SD_D9, EXT_D9 GNDIO3 75 SD_D10, EXT_D10 SD_D11, EXT_D11 VDDIO3 SD_D12, EXT_D12 SD_D13, EXT_D13 70 SD_D14, EXT_D14 SD_D15, EXT_D15 SD_D0, EXT_D0 GNDIO2 EXT_WE# 65 SD_D1, EXT_D1
SD_D7, EXT_D7
SD_D6, EXT_D6
SD_D4, EXT_D4
SD_D3, EXT_D3
GPIO15, DAO1_DATA1, HS1
GPIO16, DAO1_DATA2, HS2
DAO1_DATA0, HS0
GPIO22, DAO2_SCLK
GPIO19, DAO2_DATA1, HS4
Figure 19. 128-Pin LQFP Pin-Out Diagram
DS752PP8 Copyright 2009 Cirrus Logic 29
GPIO18, DAO2_DATA0, HS3
SD_D2, EXT_D2
VDD1
SD_DQM0
GNDIO1
DAO1_SCLK
DAO1_LRCLK
VDDIO2
GND2
TEST
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
8.2 144-Pin LQFP Pin-Out Diagram
105 GPIO11, PCP_A3, AS#, SCP2_MISO / SDA GPIO38, PCP_WR# / DS#, SCP2_CLK
GPIO10, PCP_A2 / A10, SCP2_MOSI
108 GPIO41, PCP_IRQ#, SCP2_IRQ#
GPIO37, SCP1_BSY#, PCP_BSY#
GPIO39, PCP_CS#, SCP2_CS#
GPIO34, SCP1__MISO / SDA
GPIO40, PCP_RD# / RW#
GPIO32, SCP1_CS#, IOWAIT
100 GPOI36, SCP1_IRQ#
95 GPIO33, SCP1_MOSI
GPIO35, SCP1_CLK
75 SD_BA0, EXT_A13
SD_BA1, EXT_A14
GPIO30, XMTB_IN
90 EXT_CS1#
80 SD_RAS# SD_CAS#
EXT_OE#
EXT_A19
EXT_A18
85 EXT_A17 EXT_A16
EXT_A15
94 GNDIO6
SD_WE#
76 GNDIO5
RESET#
SD_CS#
SD_A10, EXT_A10
101 GND6
GPIO9, PCP_A1 / A9 109 GPIO8, PCP_A0 / A8 110 GPIO7, PCP_AD7 / D7 GPIO6, PCP_AD6 / D6 VDDIO7 113 GPIO5, PCP_AD5 / D5 GPIO4, PCP_AD4 / D4 115 GNDIO7 116 GPIO3, PCP_AD3 / D3 GPIO2, PCP_AD2 / D2 VDD7 119 GPIO1, PCP_AD1 / D1 120 GPIO0, PCP_AD0 / D0 GND7 122 XTAL_OUT XTI XTO 125 GNDA 126 NC PLL_REF_RES VDDA (3.3V) 129 VDD8 130 GPIO14, DAI1_DATA3, TM3, DSD3 GPIO13, DAI1_DATA2, TM2, DSD2 GND8 133 GPIO12, DAI1_DATA1, TM1, DSD1 DAI1_DATA0, TM0, DSD0 135 VDDIO8 136 DAI1_SCLK, DSD_CLK DAI1_LRCLK, DSD4 GNDIO8 139 GPIO42, BDI_REQ# , DAI2_LRCLK, PCP_IRQ# / BSY# 140 GPIO43, BDI_CLK, DAI2_SCLK BDI_DATA, DAI2_DATA, DSD5 GPIO27 GPIO26 144 10 13 15 18 21 24 25 27 30 33 35 36 1 5 9
73 VDDIO5 72 SD_A0, EXT_A0 SD_A1, EXT_A1 70 SD_A2, EXT_A2 69 GND4 SD_A3, EXT_A3 SD_A4, EXT_A4 66 VDD4 65 EXT_CS2# SD_A5, EXT_A5 63 GNDIO4 SD_A6, EXT_A6 SD_A7, EXT_A7 60 VDDIO4 SD_A8, EXT_A8 SD_A9, EXT_A9 57 GND3 SD_A11, EXT_A11 55 SD_A12, EXT_A12 54 VDD3 SD_CLKEN SD_CLKIN SD_CLKOUT 50 SD_DQM1 SD_D8, EXT_D8 SD_D9, EXT_D9 47 GNDIO3 SD_D10, EXT_D10 45 SD_D11, EXT_D11 44 VDDIO3 SD_D12, EXT_D12 SD_D13, EXT_D13 SD_D14, EXT_D14 40 SD_D15, EXT_D15 SD_D0, EXT_D0 EXT_WE# 37 SD_D1, EXT_D1 GNDIO2
91 VDDIO6
86 GND5
CS497xx4
144-Pin LQFP
GPIO20, DAO2_DATA2
GPIO21, DAO2_DATA3 / XMTB
VDD1
TEST
GPIO23, DAO2_LRCLK
GPIO17, DAO1_DATA3 / XMTA
GPIO29, XMTA_IN
DBDA
DBCK
GPIO18, DAO2_DATA0, HS3
GPIO22, DAO2_SCLK
GPIO28, DDAC
GPIO16, DAO1_DATA2, HS2
GPIO19, DAO2_DATA1, HS4
GPIO15, DAO1_DATA1, HS1
DAO1_DATA0, HS0
DAO_MCLK
DAO1_LRCLK
DAO1_SCLK
VDD2 GPIO25, EE_CS#
GND1
VDDIO1
GNDIO1
83 VDD5
98 VDD6
GND2
SD_DQM0 SD_D7, EXT_D7
SD_D6, EXT_D6
SD_D5, EXT_D5
SD_D4, EXT_D4
VDDIO2
SD_D3, EXT_D3
Figure 20. 144-Pin LQFP Pin-Out Diagram
30
Copyright 2009 Cirrus Logic
SD_D2, EXT_D2
GPIO31
GPIO24
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
9. Package Mechanical Drawings
9.1 128-Pin LQFP Package Drawing
D D1
E E1
1 e A1 L
b A
Figure 21. 128-Pin LQFP Package Drawing
Table 6. 128-Pin LQFP Package Characteristics MILLIMETERS DIM MIN NOM MAX MIN NOM MAX INCHES
A A1 b D D1 E E1 e q L L1 ddd
--0.05 0.17
0 0.45
----0.22 22.00 BSC 20.00 BSC 16.00 BSC 14.00 BSC 0.50 BSC 3.5 0.60 1.00 REF 0.08
1.60 0.15 0.27
--.002" .007"
7 0.75
0 .018"
----.009" .866" .787" .630" .551" .020" 3.5 .024" .039" REF .003"
.063" .006" .011"
7 .030"
TOLERANCES OF FORM AND POSITION
DS752PP8
Copyright 2009 Cirrus Logic
31
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
9.2 144-Pin LQFP Package Drawing
E E1
D D1
Notes: Controlling dimension is millimeter. Dimensioning and tolerancing per ASME Y14.5M-1994.
e b
SEATING PLANE ddd M B
B
L1 A A1
L
Figure 22. 144-Pin LQFP Package Drawing
Table 7. 144-Pin LQFP Package Characteristics MILLIMETERS DIM MIN NOM MAX MIN NOM MAX INCHES
A A1 b D D1 E E1 e q L L1 ddd
--0.05 0.17
0 0.45
----0.22 22.00 BSC 20.00 BSC 22.00 BSC 20.00 BSC 0.50 BSC --0.60 1.00 REF 0.08
1.60 0.15 0.27
--.002" .007"
7 0.75
0 .018"
----.009" .866" .787" .866" .787" .020" --.024" .039" REF .003"
.063" .006" .011"
7 .030"
TOLERANCES OF FORM AND POSITION
32
Copyright 2009 Cirrus Logic
DS752PP8
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
10. Revision History
Revision A1 PP1 PP2 Date FEB 2007 MAY 2007 JULY 2007 Advance Release. Removed Advanced Product watermark, corrected logo, and added "Preliminary Product Information" on first page and modified legal information to reflect Preliminary Product status. Added notice about status of DTS-HD license on page 1 and 7. Updated the Tspidsu, Tspickl, and Tspickh timing parameters for master mode SPI. This applies to both SPI ports. Removed DTS-HD license notice inserted in version PP2. The license for the DTS-HD decoder is now in place. Updated Pin Assignments in 144-Pin LQFP Pin-Out Diagram, removing EE_CS from Pin 7 and adding EE_CS to Pin 25. Updated DAO timing specifications and timing diagrams. Changed product naming conventions in Table 4 and Table 5. Changed references to CS4970x4 Hardware User's Manual to CS4970x4 System Designer's Guide. Changed references to CS4970x4 Firmware User's Manual to CS4970x4 System Designer's Guide Added 128-Pin LQFP Pin-Out and Package drawings. Changed part numbering in Section 6.and Section 7. Added device and firmware selection guide in Table 2. Added typical crystal frequency values in Table Footnote 1 and the Max and Min values of Fxtal in Section 5.8. Removed DSD Phase Modulation Mode from Section 5.17. Removed reference to MCLK in Section 5.17. Redefined Master mode clock speed for SCP_CLK in Section 5.11. Redefined DC leakage characterization data in Section 5.3, correcting units of measurement. Modified Footnote 1 under Section 5.10. Changed product family numbering from CS497xx to CS4970x4. Corrected product listings in table under Section 5.9 "Switching Characteristics -- Internal Clock" on page 13. Removed references to External Parallel Flash / SRAM Interface. Updated the feature descriptions on the first page of this data sheet. Removed references to UART port. Removed references to 11.2896, 18.432, and 27 MHz frequency clocks in Note 1 in Section 5.8 "Switching Characteristics -- XTI" on page 12 and the Min and Max External Crystal Operating Frequency values in that same section. Added Section 5.6 "Thermal Data (128-pin LQFP)" on page 11. Updated Figure 9 and Figure 10. Updated Section 5.17 "Switching Characteristics -- DSD" Serial Input Port" on page 22. Updated Figure 15 and Figure 16. In Section 5.3, the parameter, "Input leakage current (all digital pins with internal pull-up resistors enabled, and XTI)", Max value changes from 50 mA to 70 mA. In Section 5.13, the parameter SCP_CLK low to SCP_SDA out valid with symbol "tiicdov" Max value changes from 18 ns to 36 ns. Added CS497014 to Section 6. "Ordering Information" on page 28 and to Section 7. "Environmental, Manufacturing, and Handling Information" on page 28. Updated Table 2, "Device and Firmware Selection Guide," on page 5. Changes
PP3
OCT 2007
PP4
December 20, 2007
PP5
May 28, 2008
PP6
August 4, 2008
PP7
September 30, 2008
PP8
November 6, 2009
DS752PP8
Copyright 2009 Cirrus Logic
33
CS4970x4 Data Sheet 32-bit High Definition Audio Decoder DSP Family
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find the one nearest to you go to www.cirrus.com.
IMPORTANT NOTICE "Preliminary" product information describes products that are in production, but for which full characterization data is not yet available. Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, the Cirrus Logic logo designs, DSP Composer, and Cirrus Framework are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. Dolby, Dolby Digital, Dolby Headphone, Dolby Virtual Speaker, Dolby Headphone, Pro Logic, AC-3, Audistry, and Surround EX are registered trademarks of Dolby Laboratories, Inc. AAC is a trademark of Dolby Laboratories, Inc. Supply of an implementation of Dolby Technology does not convey a license nor imply a right under any patent, or any other industrial or Intellectual Property Right of Dolby Laboratories, to use the Implementation in any finished end-user or ready-to-use final product. It is hereby notified that a license for such use is required from Dolby Laboratories. DTS and DTS Digital Surround are registered trademarks of the Digital Theater Systems, Inc. DTS Neo:6, DTS-ES 96/24, DTS-ES, DTS 6.1, DTS 96/24, DTS Neural Surround, and DTS Express are trademarks of Digital Theater Systems, Inc. It is hereby notified that a third-party license from DTS is necessary to distribute software of DTS in any finished end-user or ready-to-use final product. THX Technology by Lucasarts Entertainment Company Corporation. THX is a registered trademark of Lucasarts Entertainment Company Corporation. Re-equalization and Ultra 2 are trademarks of Lucasfilm Ltd. SRS, Circle Surround and Trusurround XT are registered trademarks of SRS Labs, Inc. Circle Surround II, TruSurround HD4, and WOW HD are trademarks of SRS Labs, Inc. The CIRCLE SURROUND TECHNOLOGY rights incorporated in the Cirrus Logic chip are owned by SRS Labs, Inc. and by Valence Technology Ltd., and licensed to Cirrus Logic, Inc. Users of any Cirrus Logic chip containing enabled CIRCLE SURROUND(R) TECHNOLOGY (i.e., CIRCLE SURROUND(R) LICENSEES) must first sign a license to purchase production quantities for consumer electronics applications which may be granted upon submission of a preproduction sample to, and the satisfactory passing of performance verification tests performed by SRS Labs, Inc., or Valence Technology Ltd. E-mail requests for performance specifications and testing rate schedule may be made to cslicense@srslabs.com. SRS Labs, Inc. and Valence Technology, Ltd., reserve the right to decline a use license for any submission that does not pass performance specifications or is not in the consumer electronics classification. All equipment manufactured using any Cirrus Logic chip containing enabled CIRCLE SURROUND(R) TECHNOLOGY must carry the Circle Surround(R) logo on the front panel in a manner approved in writing by SRS Labs, Inc., or Valence Technology Ltd. If the Circle Surround logo is printed in users manuals, service manuals or advertisements, it must appear in a form approved in writing by SRS Labs, Inc., or Valence Technology, Ltd. The rear panel of Circle Surround(R) products, users manuals, service manuals, and all advertising must all carry the legends as described in LICENSOR'S most current version of the CIRCLE SURROUND Trademark Usage Manual. Microsoft and Windows Media are registered trademarks of Microsoft Corporation. The product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc. , HDCD, High Definition Compatible Digital and Pacific Microsonics Inc. are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. HDCD technology provided under license from Microsoft Corporation. The product's design (and/or software) is covered by one or more of the following: 5,479,168; 5,638,074; 5,640,161; 5,808,574; 5,838,274; 5,854,600; 5,864,311; 5,872,531 with other patents pending. Supply of this product does not convey a license under the relevant intellectual property of Thomson multimedia and/or Fraunhofer Gesellschaft nor imply any right to use this product in any finished end user or ready-to-use final product. An independent license for such use is required. For details, please visit http://www.mp3licensing.com. Motorola and SPI are trademarks of Motorola, Inc. Intel is a registered trademark of Intel Corporation. I2C is a trademark of Philips Semiconductor. DSD, and Direct Stream Digital are registered trademarks of SONY KABUSHIKI KAISHA CORPORATION.
34
Copyright 2009 Cirrus Logic
DS752PP8

▲Up To Search▲

Price & Availability of CS497014-CVZ

	To Download CS497014-CVZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .